-
- Micron ratings from 1 to 200
- All industry standard & custom sizes available
- Broad chemical compatibility
- High flow/low pressure drop
- Sewn or fully-welded construction
- Handles on all bags
- Choice of steel ring or plastic flange
- Temperature ratings to 200ºF (PO), 275ºF (PE ), 425ºF (HT) and 500ºF (Teflon®)
-
BH - Bag Housings
(26)- Available in single to 10 bags (or more) per housing
- 100 or 150 psi models available
- ASME section VII U-stamped housings are available upon request
- Available in Size 1, Size 2, and up to Size 12
- Available with threaded clamp or swing bolt lid closures
-
- Micron ratings from 1 to 200
- All industry standard & custom sizes available
- Broad chemical compatibility
- High flow/low pressure drop
- Sewn or fully-welded construction
- Handles on all bags
- Choice of steel ring or plastic flange
- Temperature ratings to 200ºF (PO), 275ºF (PE ), 425ºF (HT) and 500ºF (Teflon®)
-
- Indicates critical pressure drops or when to change or clean a filter
- Colored bands allow you to quickly identify pressure drop across element
- Green (clean), Yellow (change), Red (Dirty) indicators
-
- Micron ratings from 1.0 to 50.0.
- Wide chemical compatibility
- Excellent oil absorbing capabilities
- NEARLY 11 POUNDS OIL RETENTION CAPACITY!
- Efficiencies to 95.0%.
-
- Depth and pleated technologies provide high flow/high dirt holding capacity
- Inside to out flow traps contaminant inside the element
- Fits in standard #1 or #2 bag housings
- Greatly reduces operating/maintenance costs
-
- Made of a polypropylene resin
- Meets FDA regulation 21CRF177.1520
- Certified under ANSI/NSF standard 42
- Provides high flow rates with minimum pressure drops
- Graduated density provides twice the life of other manufactures
-
- Constructed of polypropylene meltblown microfibers
- 93-97% efficient depending on micron level
- Each bag can handle flows up to 60 GPM
- Easy to use, convenient, high performance alternative to filter cartridges
-
- Duplex housings permit continuous operation
- Process is uninterrupted and thus reduces overall operation costs
- Two separate chambers that operate independently
- Allows one side to be serviced while the other is in use
- Constructed of either carbon steel, 304 stainless steel, or 316 stainless steel
-
- Micron ratings from 1 to 200
- All industry standard & custom sizes available
- Broad chemical compatibility
- High flow/low pressure drop
- Sewn or fully-welded construction
- Handles on all bags
- Choice of steel ring or plastic flange
- Temperature ratings to 200ºF (PO), 275ºF (PE ), 425ºF (HT) and 500ºF (Teflon®)
-
- Micron ratings from 1 to 200
- All industry standard & custom sizes available
- Broad chemical compatibility
- High flow/low pressure drop
- Sewn or fully-welded construction
- Handles on all bags
- Choice of steel ring or plastic flange
- Temperature ratings to 200ºF (PO), 275ºF (PE ), 425ºF (HT) and 500ºF (Teflon®)
-
- Micron ratings from 1 to 200
- All industry standard & custom sizes available
- Broad chemical compatibility
- High flow/low pressure drop
- Sewn or fully-welded construction
- Handles on all bags
- Choice of steel ring or plastic flange
- Temperature ratings to 275ºF
-
- Absolute (98%) micron ratings from 3 - 100 micron
- Microfiber layers are thermally-bonded and contain no adhesives, resin or silicone
- Graded-layer configuration provides low initial pressure drop and maximum dirt holding capacity
- Wide chemical compatibility
-
Magnetic Insert Bag Housing